Proudly made in the USA
The ODP 30-4 is a four drum puller capable of line pull of 3,000 lbs on a single drum. Each drum can be engaged or disengaged for single or multiple drum pulling. An overspin brake with a hydraulic actuator is also included on each drum. Operator controlled post style levelwind allows for even winding of rope.
All unit functions are centrally located at the operators station. Engine gauges including tachometer, oil pressure, temp, fuel, and voltage are all in view. Pulling is controlled with an electric over hydraulic, spring return to nuetral joystick allowing for infinite control of line speed and pre-settable line pull.
Performance
- 3,500 PSI maximum hydraulic pressure at full performance
- 31,000 in-lb continuous torque rating
- 37,000 in-lb intermittent torque rating
- Infinitely variable linepull speed (full drum) from 0-4.0 mph
Drum Capacity
- Four pulling reels with individual mechanical engagement at each reel
- Reel is 44” diameter, 27” between flanges with a 12” core
- Capacity of 15,000 ft per reel of .5 inch or 10,000 ft per reel of .625
- Stainless steel overspin brakes with hydraulic calipers
- Reel shaft mounted on pillow block and flange bearings
- Hydraulic post style level wind (2) rear of trailer. (4) Optional
Hydraulic Reel Drive System
- Drive system with spring applied hydraulic release holding brake rated at 150% of rated machine torque
- Braking system applies automatically in event of pressure loss.
- Manual holding brake control
- Variable displacement hydraulic pump with electric variable speed control
- Hydraulic oil cooler
- 31 gallon hydraulic reservoir with oil level and temp gauge
Engine
- Yanmar 4TNV88-DSA 47.5 hp water cooled diesel
- 23 gallon fuel tank with gauge
- Optima Red Top battery
- Lockable steel battery box
- Direct Mount hydraulic
Unit Dimensions
- Length: 16’-6” (198″)
- Width: 8’-0” (96″)
- Height (shield Up): 8’-1-1/2” (97.5″)
- Height (Shield Down): 6’-9” (83″)
- Weight (with rope and fluids): 10,720 lbs.
- Tongue weight: 940 lbs. (approx.)
Control Console
- The control console is positioned in the center of the trailer tongue to provide optimum visibility and safety
- Laser Engraved operators panel with Rowmark Lasermax to a depth of .003 inches
- Hydraulic pressure gauge and Nominal line pull chart for line pull estimation
- Spring return to neutral control joystick for take up and pay out functions
- Levorsi Marine gauges with four gauge cluster and tachometer with hour meter
- Pay out lockout switch to prevent unintentional payout of rope or conductor
- Adjustable line pull pressure control
- Operator’s protection screen
- Operator’s seat
Trailer & Undercarriage
- Tandem axle with 7,000 lb capacity, spring leaf type with 12V electric brakes and breakaway switch
- Break away chains ½” X 36” with hooks and premier #9 weldments
- Tires meeting or exceeding the GAWR of unit
- Lighting system in accordance with FMVSS 108
- Conspicuity System in accordance with FMVSS 108
- Heavy Duty crank style tongue and rear trailer jacks
- Frame is constructed of tubular steel, fully welded and gusseted
- Heavy duty gauge fenders with mud flaps
- Unit is to be painted prior to assembly.
- Blast with steel grit GM50, primed, baked, painted with two finish coats and cured for 2 hours at 140 degrees
- Paint shall be Sherwin Williams Genesis II
Rope
- Metal grit blasted, primed, baked
- 15,000 feet of ½” Samson Tenex 12 Strand Rope
- Four different colors
- Average breaking strength of 11,800 lbs
- 10,000 feet of 5/8”Samson Tenex 12 Strand Rope
- Four different colors
- Average breaking strength of 17,100 lbs
